☆产品特性/Production Features
1、外形尺寸:3.0×1.4×0.8mm
Outline package:3.0×1.4×0.8mm
2、 胶体颜色:无色透明
Lens appearance: Water Clear
3、发光效率和显色性高
High luminous efficiency and high color display
4、光谱窄,单色性好
Narrow spectrum and good single color
5、功耗低,精密恒流
Low power consumption ,precision constant current
6、硅胶封装,低衰减
Silicone package ,low brightness attenuation
☆产品应用/ Production application
1、室内室外显示屏和广告屏 2、LED吸顶灯
Indoor or outdoor displays and billboard LED ceiling lamp
3、背光源 4、LED玉米灯
Back lighting LED corn light
5、LED日光灯和球泡灯 6、LED面板灯
LED daylight tube and LED globe bulb LED Panel lights
☆尺寸图/Dimensional drawing
☆外形要求/Shape Specification
序号No.
|
项目
ITEM
|
规格要求描述
SPEC or DE
|
1
|
胶体
Lens
|
◆不可有胶体变色/No change color
◆不可有破损/No Disrepair
◆ Scratch划伤/(length ≤2.0mm,Width≤0.25mm)
◆黑点、异物/macula(≤0.25mm and ≤2EA in Encapsulation reverse)
◆气泡/bubble(≤0.3mm and ≤2EA Encapsulation reverse)
|
2
|
脚
PIN
|
◆不可有氧化/No oxidation
◆不可有极性反/No electropolar reverse
|
3
|
结构Configuration
|
◆不可封反/No Encapsulation reverse
◆脚不可松动/No PIN loosen
|
☆光电特性/Opto-Electronical Characteristics
☆最大绝对核定值/Absolute maximum ratings
参数
Parameter
|
符号
Symbol
|
数值
Value
|
单位
Unit
|
正向电流Forward Current
|
If
|
30
|
m A
|
反向电压Reverse Voltage
|
Vr
|
5
|
V
|
工作温度Operating Temperature
|
Topr
|
-40~+80
|
℃
|
储存温度Storage Humidity
|
Tstg
|
-40~+85
|
℃
|
功率消耗Power Dissipation
|
Pd
|
100
|
m W
|
抗静电能力 Electrostatic Discharge
|
ESD
|
4000
|
V
|
脉冲电流Pulse Current
|
Ifp
|
100
|
m A
|
☆光电参数规格/Opto-Electronical Specification
参数
Parameter
|
符号
Symbol
|
最小值
Min
|
平均值
Typ
|
最大值
Max
|
单位
Unit
|
误差值
Tolerance
|
测试条件
Test Conditinos
|
正向电压
Forward Voltage
|
Vf
|
3.0
|
3.3
|
3.6
|
V
|
± 0.05V
|
F/正向电流=30mA
测试温度=25℃
Test Temperature
|
发光强度
Luminous Intensity
|
IV
|
3500
|
--
|
4000
|
mcd
|
± 60 mcd
|
|
色温
Color Temperature
|
TC
|
5500
|
--
|
6500
|
k
|
±100k
|
|
光通量
Luminous Flux
|
Φ
|
11.5
|
12
|
12.2
|
Lm
|
±0.15 Lm
|
|
发光角度
Lighting Angle
|
2θ1/2
|
125
|
130
|
135
|
deg
|
±3
|
|
反向电流
Reverse Current
|
IR
|
--
|
--
|
10
|
μA
|
±0.1μA
|
Vr=5V
|
☆可靠度测试项目/Reliability Test Items
No.
|
测试项目
Item
|
测试条件
Condition
|
测试时间或周期
Time/Cycle
|
不良数/测试数
Number of Damaged
|
1
|
焊接试验
Soldering Heat Test
|
260±5 ℃
|
10 sec
|
0/60
|
2
|
热冲击
Thermal Shock
|
0 ℃~100 ℃(15sec)
|
20 cycle
|
0/60
|
3
|
高温储存
High Temp. Storage
|
100 ℃
|
1000Hrs
|
0/60
|
4
|
低温储存
Low Temp. Storage
|
-40 ℃
|
1000Hrs
|
0/60
|
5
|
高低温循环
Temperature Cycle Test
|
-40 ℃ ~ 80 ℃
|
100 Cycles,
200 Hrs
|
0/60
|
6
|
高温高湿
High Temp. High Humidity Test
|
60 ℃, 90 % RH
|
1000Hrs
|
0/60
|
7
|
常温老化
Operation Life Test 1
|
Room Temp, 20mA
|
1000Hrs
|
0/60
|
8
|
常温老化
Operation Life Test 2
|
Room Temp, 30mA
|
500 Hrs
|
0/60
|
9
|
常温老化
High Temp. Operation Life Test
|
85 ℃ , 5mA
|
1000 Hrs
|
0/60
|
10
|
常温老化
Low Temp. Operation Life Test
|
-40 ℃ , 20mA
|
1000 Hrs
|
0/60
|
☆判定标准/Judgment Criteria
项目
Item
|
符号
Symbol
|
测试条件
Test Conditions
|
判断标准
Judgment Criteria
|
正向电压
Forward Voltage
|
Vf
|
IF = 30 mA
|
Δ% < 10 %
|
反向漏电流Leakage Current
|
Ir
|
Vr = 5V
|
< 10 uA
|
发光强度
Luminous Intensity
|
Iv
|
IF =30 mA
|
Δ% <10 %
|
光通量
Luminous Flux
|
lm
|
IF =30 mA
|
Δ% <10 %
|
※温馨提示:以上所有参数均为多次实验后所得的一个统计学参数,因具体使用芯片等原材料和测试设备不同会有微小差异。相关颜色和参数等可根据客户要求差异化定做。相应产品未详列的规格部分可致电我公司索取,我们将热忱为您提供满意的服务。顺祝商祺!
☆注意事项/Caution
1、打开包装后请在温度25±3℃, 湿度65±5%的环境下使用。
After open the package, the LED should be kept at 25oC, 65 % RH environment or less.
2、打开包装后请在6小时内做焊接。
The LED should be soldered within 6 hours after opening the package.
3、LED 是静电敏感器件,使用時所有设备都需有适当的接地导电措施。
The LAMP LED is an ESD sensitive device. All the equipment and machine must be properly grounded.
4、使用时请使用防静电的盛裝容器,作业人员应穿着防静电服装及佩戴有绳之静电环并作有效接地。
When make use of it ,please use static-free container ,operator showld ware antistatic clothes and rope-satic-ring also should make effective ground.
5、受静电与突波破坏之LED 的电性特性上,会有明显的漏电流,或驱动电压明显变低,甚至是短路现象。
Damaged device will appear some symptoms ,lower forward voltage ,higher leak current ,or even short circuit.
6、烙铁焊接时烙铁功率不要超过40W,尖端温度不要超过280 ℃,焊接时间不要超过3 秒。
Ferrochromium soldering power keep no more than 40W,tip temperature should not pass 280 ℃,soldering time within 3 second.
7、在焊接温度回到正常以前,必须避免使LED 受到任何震动或外力。
After soldering the LED should keep out off any shake or outer force before it come to normal tempreture.
8、单向导通性,安裝前确认极性,若装反在施加电压时容易造成LED 晶片损伤或失效。
LED is one-way continuity, please check electrode before mount, if amount wrong ,the LED chip will damage or fail when LED applied voltage.
9、线路设计时,请不要将LED 与发热元件靠得过近。
Please design the PCB board to keep a distance between LED and other emit heat component.
10、电路设计上建议以定电流设計,若为定电压设计请考虑LED之间不同正向电压所可能造成之影响。
Strongly recommend design the board according setting current other than setting voltage .if you are really need setting voltage type please consider there may cause influence arise by difference voltage of difference LED.
11、LED之外加电压变化会造成电流指数极变化,不当之设计与电流控制易造成LED失效。如电流过大引起寿命问题甚至烧毁,电流过小引起亮度不足。
The outer voltage change will bring the current index change .unsuitable design and current control ,easy cause LED fail .for example excess current will cause LED life short or even burn down , too little electricity will cause lacking light.
12、不同BIN 号之LED需安裝在同一个组件时,请先确认是否可满足相关电气及光学之特性要求。如电流是否均衡,光色、亮度的一致性等。
If you need make difference BIN LED in the one module .please confirm whether it can meet the electric and optics characteristic require such as the current balance, emitting and brightness consistency.
☆其他产品附表/Other productions schedule
LED SMD3014 0.1W其他产品光电参数
发光颜色
Emitting Color
|
产品型号
Model
|
正向电压
Forward Voltage(v)
|
正向电流
Forward Current(mA)
|
色温或波段
CCT(k) or WD(nm)
|
光通量或发光强度
Φ(lm)or IV(Mcd)
|
角度
Bean angel(°)
|
暖白(Warm white)
|
SY-3014-WW01
|
3.0—3.6
|
30
|
2500-4000
|
11-12
|
130
|
蓝色(Blue)
|
SY-3014-BE01
|
3.0—3.6
|
30
|
460-465
|
1400-1800
|
130
|
绿色(Green)
|
SY-3014-GN01
|
3.0—3.6
|
30
|
520-525
|
1600-2400
|
130
|
红色(Red )
|
SY-3014-RD01
|
1.8—2.4
|
30
|
620-625
|
500-1100
|
130
|
黄色(Yellow)
|
SY-3014-YW01
|
1.8—2.4
|
30
|
585-590
|
500-1200
|
130
|
LED SMD5050 0.2W其他产品光电参数
发光颜色
Emitting Color
|
产品型号
Model
|
正向电压
Forward Voltage(v)
|
正向电流
Forward Current(mA)
|
色温或波段
CCT(k) or WD(nm)
|
光通量或发光强度
Φ(lm)or IV(Mcd)
|
角度
Bean angel(°)
|
正白(Pure white)
|
SY-5050-PW02
|
3.0—3.6
|
60
|
5500-6500
|
10-20
|
120
|
暖白(Warm white)
|
SY-5050-WW02
|
3.0—3.6
|
60
|
2500-4000
|
10-20
|
120
|
蓝色(Blue)
|
SY-5050-BE02
|
3.0—3.6
|
60
|
460-465
|
600-1800
|
120
|
绿色(Green)
|
SY-5050-GN02
|
3.0—3.6
|
60
|
520-525
|
1800-3000
|
120
|
红色(Red )
|
SY-5050-RD02
|
1.8—2.4
|
60
|
620-625
|
800-1500
|
120
|
黄色(Yellow)
|
SY-5050-YW02
|
1.8—2.4
|
60
|
585-590
|
600-1500
|
120
|
RGB
|
SY-5050-RGB02
|
1.8—2.4
|
60
|
620-625(R)
|
300-500
|
120
|
3.0—3.6
|
60
|
520-525(G)
|
600-1200
|
120
|
||
3.0—3.6
|
60
|
460-465(B)
|
250-600
|
120
|
LED SMD3528 0.065W其他产品光电参数
发光颜色
Emitting Color
|
产品型号
Model
|
正向电压
Forward Voltage(v)
|
正向电流
Forward Current(mA)
|
色温或波段
CCT(k) or WD(nm)
|
光通量或发光强度
Φ(lm)or IV(Mcd)
|
角度
Bean angel(°)
|
正白(Pure white)
|
SY-3528-PW65
|
3.0—3.6
|
20
|
5500-6500
|
7-9
|
120
|
暖白(Warm white)
|
SY-3528-WW65
|
3.0—3.6
|
20
|
2500-4000
|
7-9
|
120
|
蓝色(Blue)
|
SY-3528-BE65
|
3.0—3.6
|
20
|
460-465
|
350-500
|
120
|
绿色(Green)
|
SY-3528-GN65
|
3.0—3.6
|
20
|
520-525
|
400-600
|
120
|
红色(Red )
|
SY-3528-RD65
|
1.8—2.4
|
20
|
620-625
|
200-280
|
120
|
黄色(Yellow)
|
SY-3528-YW65
|
1.8—2.4
|
20
|
585-590
|
500-900
|
120
|
RGB
|
SY-3528-RGB65
|
1.8—2.4
|
20
|
620-625(R)
|
180-250
|
120
|
3.0—3.6
|
20
|
520-525(G)
|
350-500
|
120
|
||
3.0—3.6
|
20
|
460-465(B)
|
300-400
|
120
|
LED T10 汽车灯1W其他产品光电参数
发光颜色
Emitting Color
|
产品型号
Model
|
正向电压
Forward Voltage(v)
|
正向电流
Forward Current(mA)
|
色温或波段
CCT(k) or WD(nm)
|
光通量
Luminous flux(Lm)
|
角度
Bean angel(°)
|
正白(Pure white)
|
SY—T10—PW10
|
3.0-6.0
|
300
|
5500-6500
|
100-110
|
135
|
暖白(Warm white)
|
SY—T10—WW10
|
3.0-6.0
|
300
|
2500-4000
|
90-100
|
135
|
蓝色(Blue)
|
SY—T10—B10
|
3.0-6.0
|
300
|
460-465
|
45-55
|
135
|
绿色(Green)
|
SY—T10—G10
|
3.0-6.0
|
300
|
520-525
|
50-60
|
135
|
红色(Red)
|
SY—T10—R10
|
1.8-2.4
|
300
|
620-625
|
40-50
|
135
|
黄色(Yellow)
|
SY—T10—Y10
|
1.8-2.4
|
300
|
585-590
|
40-50
|
135
|