球泡灯内置驱动电源 PAR38-12A2

 
 
单价 面议对比
询价 暂无
浏览 629
发货 广东深圳市预售,付款后10天内
库存 1000000个起订10个
品牌 LED电源
输入电压 90-264VAC
输出电压 18-24VDC
功率 9-12W
过期 长期有效
更新 2014-01-11 09:19
 
联系方式
加关注0

深圳市鑫达尔康电子有限公司.

企业会员第11年
资料未认证
保证金未缴纳
详细说明

MODEL 产品型号

PAR38-12A2043AU-PF

输入特性

Input

 

输入电压范围Input Voltage

90VAC~264VAC

 

额定输入电压范围Voltage Range

100VAC~240VAC

 

启动电压Start-up Voltage(-25~70℃)

90VAC

 

输入频率范围Frequency Range

47Hz~63Hz

 

功率因数Power Factor(@25℃)

>0.95@220VAC, 满载Full Load.

 

输入电流AC Current (@25℃)

0.160A 最大值Max.

 

启动冲击电流Inrush Current (@ 25℃)

10A 最大值Max.

输出特性

Output

 

恒流输出电压范围Output Voltage Range 

18V~24V

 

输出电流Output Current

425mA  

 

额定输出功率Output Power

9~12W

 

转换效率Conversion Efficiency (@25℃)

86% @220VAC, 满载Full Load

 

空载输出电压范围No-load Output Voltage

36V最大值Max.

 

源调整率Line Regulation (@-25~70℃)

±5%

 

恒流精度Accuracy Constant(@-25~70℃)

±5%

 

输出启动时间Set-up Time(@25℃)

<1S@220VAC, <2S@110VAC

 

温度系数Temperature Coefficient(@-25~70℃)

±0.03%/℃

 

电压过冲Overshoot (@-25~70℃)

±5% 空载额定电压 No-load Rated Voltage

 

输出纹波和噪声

Output Ripple & Noise

0<Ta≤70℃

850mVP-P

 

 

-25≤Ta≤0℃

2000mVP-P

保护功能

Protection

(-25~70℃)

 

输入

Input Electrical

欠压保护

Low Voltage Protection

/

 

 

过压保护

Over Voltage Protection

/

 

输出

Output Electrical

短路保护

Shorted Circuit Protection

荡机,自恢复  Hiccup, Auto Recovery

 

 

空载保护

No-load Protection

恒压  Constant Voltage

 

过温保护Over Temperature Protection

/

工作环境Environmental Requirement

 

振动Vibration

10~500Hz,2G 10分钟/1圈,沿X、Y、Z轴每60分钟为一周期。 10~500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z, axes

 

冲击Impact

20G/11mS脉冲,X、Y、Z轴分别3次。

20G/11mS pulse,3times at each X, Y, Z axes

 

储存温度与湿度Storage Temp. & Hum.

-40℃~85℃; 10%~95%RH 非冷凝No condensing

 

工作温度与湿度Operating amb. Temp. & Hum.

-40℃~60℃; 20%~90%RH 非冷凝No condensing

 

海拔高度Altitude

3000m

 

防水等级IPX

/

安全及电磁兼容标

EMC

绝缘阻抗Isolation Resistance

输入—输出Input--out: 100M OHMS

 

绝缘强度Withstand Voltage

输入—输出Input--out: 3KVAC/10mA

 

接地阻抗Ground Impedance

/

 

安全标准Safety Standards

IEC 61347-2-13/GB19510.14/UL8750 ■ 参考  □ 认证     

 

电磁干扰性EMI

CE 传导干扰

EN55015 Class B/FCC Part15 B

 

 

RE 辐射干扰

EN55015 Class B/FCC Part15 B

 

谐波Harmonic Current

EN6100-3-2, Class C

 

电磁抗干扰性EMS

传导干扰CS

EN61000-4-6 Level  2  Class B

 

 

辐射干扰RS

EN61000-4-3 Level  2  Class B

 

 

静电干扰ESD

EN61000-4-2 Level  2  

 

 

雷击SURGE

EN61000-4-2 Level  2  

 

 

工频干扰

Power Frequency Harassment

EN61000-4-8 Level  2

 

 

快速脉冲EFT

EN61000-4-4 Level  2  

其他Other

尺寸 (长*宽*高)Dimensions (L * W * H)

50mm X 50mm X 20mm;±1mm

 

净重Weight

38.5g;±1g

 

包装Package

/

 

冷却方式Cooling Method

自然风冷却Ventilation Cooling

可靠性要求Reliability

老化Burn-in

产品至少满载条件下老化4小时。The power supply shall go a minimum of 4 Hours burn-in test under full load condition.

 

设计MTBF  Design MTBF

用MIL-HDBK-217方法2,25℃下,理论寿命50000小时

50,000Hrs @25℃, MIL-HDBK-217 Method 2 Components Stress Method

 

设计电解电容寿命

Design electrolytic capacitor life

在负载满载和50℃状态下, 17520小时连续工作。

17520Hrs @50℃ Full load and units continuously working

注释Note

1、纹波噪声是利用12#双绞线连接,且在20MHz带宽,并联 0.1uF和10uF电容。

Measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1 uF & 10uF parallel capacitor.

2、测试备件:试验电压为500VDC,65%RH@25℃。

Test spare parts: test voltage for 500 VDC, 65% RH @ 25 ℃.

3、电源将会作为一个部件装在最终设备上,最终的设备仍需满足EMC条件。

The SPS is considered a component which will be installed into final equipment. The equipment must be re-confirmed that it still meets EMC directives. 

最小负

载要求Minimum Negative Load Requirements

无  None 

附件

Accessories

/

■ 机械性能Mechanical Specification: 

Pin Connection连接器脚位定义             

Power AC Input 输入

 

编号NO.

功能Function

颜色Color

详细说明Specifications

L

白色White

UL1015 VW-1   105℃ 600V  26AWG  100mm

2

N

白色White

 

DC Output 输出

编号NO.

功能Function

颜色Color

详细说明Specifications

DC+

红色Red

UL1015 VW-1   105℃ 600V  26AWG  100mm

2

DC-

黑色Black

 

■  安装使用说明Installation &. Instruction 

 

1、使用时请注意区分输入端与输出端,以及输出端的正负极性,核对无误后才能通电;

Before connecting this unit, please make sure that the input and output terminal, and the positive and negative polarities of output terminal are on the right position respectively.

2、本产品皆为高压回路,使用时注意安全,并做好防电击措施,安装时必须避免与金属外壳短路; 

Because of high tension loop of this unit, please pay much attention to your safety and anti-electric shock measurement is necessary. While installing, please make sure that this unit is kept off the metal shell.

3、使用时请勿超过电源标称值,以免影响产品的可靠性。如需更改电源的输出参数,请客户在使用电源前向本司技术部门咨询,以保证使用效果和可靠性。

In order to avoid effecting the reliabilities of this unit, please do not use the power which is exceed what the unit marked. If any output parameters need to be changed, please inquire the technical staff of our company.

 

 

 

 

举报收藏 0
更多>本企业其它产品
内置驱动电源 AR111-12A1 日光灯管内置驱动电源  DEK-T8-12W 日光灯管内置驱动电源  DEK-T8-30W 球泡灯内置驱动电源 PAR30-08A1 球泡灯内置驱动电源 PAR30-07A1 内置驱动电源 MR16-03E2 内置驱动电源 MR16-03B1 内置驱动电源 MR16-03E3
网站首页  |  关于我们  |  联系我们  |  使用协议  |  隐私政策  |  网站地图  |  排名推广  |  RSS订阅  |  违规举报