一、 electrical parameters（电气参数）
|
Testing project 测试项目 |
Testing condition测试条件 |
Scope 范围 |
Unit单位 |
Remark 备注 |
|
Input voltage range输入电压 |
AC90-265 |
265 |
|
|
|
Normal voltage range标称输入 |
AC90-265 |
AC90-265 |
V |
|
|
Operating frequency工作频率 |
常规 |
47-63 |
Hz |
|
|
Input current输入电流 |
Vin=AC230V |
≤0.065 |
A |
|
|
Input power输入功率 |
Vin=AC100-265V |
≤13 |
W |
|
|
Input Fuse输入保险 |
Vin=230V浪涌电流小于10 |
A |
|
|
|
Power factor功率因素 |
Vin=100-240V |
≥0.95 |
|
|
|
Vin=100-240V |
≥0.95 |
|
||
|
Efficiency效率 |
Vin=AC100V |
88% |
|
|
|
Vin=AC220V |
88% |
|
||
|
Harmonic current谐波电流 |
|
|
/ |
|
|
Vin=150--230V |
15%≤ |
/ |
|
|
|
Output voltage输出电压 |
Iout=190mA |
DC57-70 |
V |
|
|
Output current输出电流 |
DC57-70V |
190 |
ｍA |
±5% |
|
Output power输出功率 |
AC100-265V |
≤13 |
W |
|
|
Short circuit power短路功耗 |
AC100-277V |
≤0.5 |
W |
|
|
No-loadpower空载功耗 |
AC220V |
≤0.2 |
W |
|
|
No-load voltage空载电压 |
AC220V |
≤100 |
V |
|
|
Ripple纹波 |
AC100-277V |
≤10 |
V |
|
|
Work mode工作模式 |
DC25-31V |
315 |
ｍA |
±5% |
|
Compression耐压 |
输入对输出 |
/ |
/ |
|
|
Isolation绝缘性能 |
/ |
/ |
/ |
|
|
LED light for适用灯串 |
VF=3-3.5V |
18-22串 |
|
|
rotective value（保护性能）
1、Open protection: when the output when open, input normal input, the product will not damage, and open voltage can't more than ratings.
开路保护：当输出端开路时， 输入端正常输入， 产品不会损坏,且开路电压不会超过额定值。
2、Short circuit protection: if the output appears unusual, causes the product of anode and short sub, this product will start short circuit protection function, and not because this abnormality in product permanent damage.
短路保护：如果输出端出现异常， 造成产品正负极短接， 本产品会启动短路保护功能， 不致因为此异常造成产品永久性损坏。
3、Overload protection: this product is the constant flow design, the LED lights in the design of the product value VF voltage range, the product output current will be constant; When LED lamp of the design of value over VF voltage range, the product will enter overload protection status.
过载保护：本产品为恒流设计,LED灯的VF值在产品的设计电压范围内时,此产品的输出电流会恒定不变;当LED灯的VF值超过所设计的电压范围时,产品会进入过载保护状态。
4.3.1、Output voltage is too low, the power supply will enter frequent start and shut off, at this time will frequently LED twinkle.
输出端电压过低,电源会进入频繁启动和关断，此时LED灯会频繁闪烁。
4.3.2、The output voltage of the too high, this product into the constant pressure to protect state, this time the LED lights on the luminous intensity pronounced weakening, current is unable to achieve the ratings.
输出端电压过高,本产品进入恒压保护状态,此时LED灯的发光强度明显变弱，电流无法达到额定值。
5、Dimension物理尺寸
产品尺寸：37*18.4*13mm(长*宽*高)
二、Environmental Requirement环境要求
This part describes the constant current drive power LED to use and storage environment.
这一部分描述了LED恒流驱动电源使用和存储环境。
1、Using temperature and humidity使用温度和湿度
1.1、Using temperature range: from 0℃to 55℃
使用温度范围：从0℃到55℃
1.2、Use humidity range: from 5 RH % to 95 RH %
使用湿度范围：从5RH%到95RH%
2、Storage temperature and humidity存储温度和湿度
2.1、Storage temperature range: from -20℃ to 80 ℃
存储温度范围：从-20℃到80℃
2.2、Storage humidity range: from 5 RH % to 95 RH %
存储湿度范围：从5RH%到95RH%
Product testing structure（产品测试结构图）
1、testing schematic diagram测试原理图：
 |
2、product interface diagram接口图示：
This product has two connection port. 'AC-L' and 'AC-N' for product AC input terminals. Used to meet in AC AC input (input 90-265 V / 47 Hz-63 Hz alternating current) for another marked 'LED +' and 'LED-' ports used to pick up the lamps and lanterns of LED, specific the wiring diagram is as follows:
本产品有两个接线端口 。'AC-L’与 'AC-N’ 为产品的AC输入端子.用于接在交流AC输入端 （输入90 -265V/47Hz-63Hz交流电）另为标有 ' LED+'与’LED- ' 的端口用于接LED的灯具.具体接线图如下：
3、product precautions产品使用注意事项：
3.1, in the device the power supply, please pay attention to the correct installation of input, output, confirms to the rear can electrify.
3.2, in order to avoid LED burn out, please take good DC output terminal open again power supply.
3.3, in the use of the products please pay attention to high pressure safety, and completes the shock measures to avoid when installation and metal case short circuit, and don't force or throw the power on extrusion of components, or in the set of casing please don't use too much about the long time at a point in heating.
3.4, power in the first time when a current good device, such as a bright lights or signal, please promptly ac power supply, and check input exchange or the output is bad contacts or overload or short circuit and remove the faults can, if there is a bright or dim light, please promptly ac power supply, and inspection of the parameters are needed to get LED anastomosis and remove the faults can.
3.5, good electrical connections in the device, LED light but a flickering or WeiLiang, please check the power supply output terminal for contact undesirable or appears light load. Overload.
3.6, as in use process in time if you have any questions please contact with our company technical support, and feedback unhealthy phenomenon, my company will have professional technical staff of the service you.
3.1、在装置电源时，请注意输入、 输出端的正确安装， 确认无误后方可通电。
3.2、为了避免LED烧坏，请先接好DC输出端再开电源。
3.3、在使用本产品时请注意高压安全， 并做好防电击措施， 安装时避免与金属外壳短路， 同时不要强行挤压或扳动本电源上的元器件，或在套套管时请不要用过高的风筒长时间在一个点上加温。
3.4、电源在第一次装置好通电时，如出现灯不亮或灯闪时，请及时切断交流供电，并检查输入交流或输出端是否接触不良或过载或短路，排除故障即可，如出现灯过亮或暗淡时，请及时切断交流供电，并检验所接用的LED所需参数是否吻合，排除故障即可。
3.5、在装置好电气连接后， LED灯亮但有闪烁或微亮，请检查电源输出端有无接触不良或出现轻载.过载。
3.6、如在使用过程中如有疑问请及时与本公司技术支持联系，同时反馈不良现象，我公司将有专业的技术人员全程为您提供服务。
